electric wax warmer Paraffin wax warmer/heater / Hand and foot care
1: Place the machine on a flat surface and lift up the lid
2: Put the paraffin wax into the machine and put the lid back on
3: Connect the machine into the power and the screen shows “OFF”
4: Here are 2 modes for choice -
A: If you choose customized temperature mode, please just press
“on/off” button then press “+”or ”-” buttons to set your desired
(Temperature range is 35~75℃. The screen will show the spacific
temperature after 5 seconds you set)
B: If you choose auto temperature mode, please press the “on/off”
button for 3-5 seconds, when the screen shows “A-U”, the machine
will start working and the temperature cannot be controlled during
this 80 minutes; After 80 minutes, the machine will keep at
5: After the wax has melted, turn off the machine (Just press the
“on/off” button for 3-5 seconds) and put the heat insulating
grid into the machine.
6: Check for suitable temperature before using the wax
7: Clean your skin completely before the treatment
8: Use the brush/silicone spatula to spread an even layer of wax
onto your hands/the area you’re going to wax and wait for the wax
9: After the wax has dried, slowly dip your hands into the melted
wax, with your fingers outstretched
10: Leave your hands in for 20-30 seconds
11: Relate steps 9 and 10 at least 4-5 times until it forms a thick
layer on your skin
12: To help achieve a better effect, wrap your hands with the glove
liner and put on a pair of heat-preservation cotton gloves
13: After 10-20 minutes, take off the gloves and get rid of the
liner and remove the wax.
A: There are 2 modes about the temperature setting:
Customized temperature mode & Auto temperature mode .
B: For Customized temperature mode:
You can press the "ON/OFF" button to make the machine start
Once started, the screen shows "35℃", which means the machine will
start heating at a constant temperature of 35℃.
You can press the "+" or "-" buttons to set the desired
temperature, and the range setting is 35~75℃;
The screen will switch to display the actual temperature after 5
C: For Auto temperature mode:
You can press the "ON/OFF" button for 3-5 seconds to enter this
At this time, the screen will show "A-U" which means heating time
is 80 minutes and heating is in a countdown mode. During this
period, "+" or "- " button is invalid;
The first 42 minutes,the machine will become 90℃ to heat, after 42
minutes, the temperature will start to cool down to 55℃.
When the time runs out, the actual temperature will be displayed ,
and when the temperature reaches 55℃, the buzzer will give three
beeps which is indicating that the wax melting is completed. Then
you can press the”ON/OFF” button to switch to the constant
temperature heating at 55℃.
1. You must feel the temperature of wax on the wrist before using.
2. Do not use on the injured skin.
3. Do not use on skin with whelk.
4. Do not pour the wax when it is melting, please cool the wax
first, then turn on the power to melt the bottom of wax and pour
the whole wax.
5. Please wait at least 1 minute before turn on again.
6.Do use the same voltage as marked on the warmer.
7.Please turn on again when the warmer is not work.
Paraffin would make the skin velvet and soft, especially for the
dry skin moisten, the effect in winter is salience. The method in
use is easy, the products has a good reputation by beautician all
over the world, either in domestic consumer. It is different from
other treatment, your customer dip in the professional wax, the
skin will become velvet and soft at once.
- Whats app: 0086 133 16277085
- Hongkong Head Office: 15/B1,15/F Cheuk Nang Plaza, 250 Hennessy
- Guangzhou Office: Room 508 Lijun Business Center, 170 Jianshe Bei
- Telephone: 0086 20 2980 3982
Photo of products: